Three car entries make a class.
​
​
ROAR class rules
​
DODC class rules
​
​
International Scale Sports Cars class rules
​
DLMRA 1/5 & 1/8 DIRT OVAL RULES
​
​
​
THUNDER TRUCKS 1/18
​
Any 1/18 rtr box stock
Spoiler allowed no taller than cab roof.
NO MODS ALLOWED
Must be brushed body kits lipo battery ok.
​
SPEC MUDBOSS 1/18
​
Box stock Traxxas LaTrax
Extreme Bodies by JB 1/18 Modified body only.
ONLY MODS ALLOWED: Traxxas bearing kit
Must be brushed motor and approved 5 cell NMHD 6V 1200mah (traxxas & Venom ONLY)
​
KIDS
RUN WHAT YOU BRUNG FREE RACING WITH PAYED ENTRY
​
​
THUNDER TRUCKS (novice)
CHASSIS
•Must be a 2/4 wheel drive SC Truck or SC Buggy.
•Stock chassis only
•Springs and Shocks must be SC based and can run any oil and piston combo.
•No adjustable rear control arms
•Control Arms must match side to side and be mounted on correct side (ex: RF and LF must be of equal length, RR and LR must be of equal length - Right side arms on right side, Left side arms on left side) and must be SCT based
•Rear toe must be the same on both sides
•Battery - no offset battery
a.) must mount in stock location in chassis
•Tires must not exceed the width of body. All tires must stay under the body.
Electronics:
•Any 2-cell 7.4 lipo (hard case only) or up to a 6 cell NiCd/NiMh
•Any speed controller. Any setting.
•Any 540 or 550 motor. No 1/8 scale motors.
•No steering or throttle assist devises of any type.
Bodies
•Any SC TRUCK body (no JConcepts Scalpel speed run Bodies or SUV type Bodies)
•Approved bodies only allowed to use 1" max rear spoiler.
- Proline Pro Touring Truck body
- JConcepts Fort Rapture Scalpel body
(Scalpel Speed Run Body NOT approved)
- Delta Plastiks NAS150
•3" max rear spoiler on approved bodies only and must mount the the furthest rear portion of the body.
•left side dam only may not be longer than rear of cab
•Windows must remain intact
•All truck bodies must have a visible number on both sides for identification and scale realism. Roof numbers are encouraged but not mandatory.
•All Thunder Truck bodies must be closed in rear of stock cut lines. Wheel wells must be open.
Wheel & Tire Specs:
•Wheels must be the 2.2/3.0 SC wheels, no 1/10 ST or 1/8 buggy
wheels
•No 1/8 wheel adapters of any kind.
•Any offset ok
•Tires must not exceed the width of body. All tires must stay under the body.
•Tires must be the 2.2/3.0 short coarse rubber tires, any compound.
​
​
​
SPORTSMAN Modified: .......
Any 2wd short course vehicle. Aftermarket chassis and components allowed. No offset chassis allowed. No offset batteries allowed. Batteries must remain in center-line with chassis.
Any servo allowed.
No Gyros or traction control devices allowed.
No external batteries allowed to power fans, receivers, or servos.
Front Suspension arms must be equal size left and right
Rear Suspension arms must be equal size left and right
Adjustable Rear Suspension arms are allowed.
ESC OPEN
MOTOR 13.5 brushless motor
Battery Any 2s2p hard case lipo or nmhd allowed absolutely no 3s and above
Body Open Wheel Modified bodies only.
TIRES ANY 2.2/3.0 SCT ONLY
​
OUTLAW Modified
​
2WD SCT DIRT Modified
Section 1:
Chassis:
Must be a 1/10 scale 2 wheel drive SC truck base. This is a builders class. Any upgrades
allowed as long as chassis fits under a 12" wide body
Wheel adapters or offset susp or chassis allowed
Any 1/10 shock set on-road/off-road (except monster truck i.e. revo ...)
Section 2:
Electronics:
RADIO OPEN
BATTERY OPEN
SPEED CONTROLLER OPEN
MOTOR OPEN
GYROS ALLOWED
Section 3:
Bodies:
Any 1/8 or SC dirt modified body production or Homemade.
No additional wings, flaps, spoilers, wickers, vents will be allowed
Decking is allowed
There will be no metal body parts of any kind.
All bodies must completely cover the rear wheels
Must run a rear bumper (No metal bumpers allowed)
Front bumpers optional but suggested
Section 4:
Rear Spoiler Specs:
Rear spoiler can only be as wide as the body at the rear quarter panels.
Rear spoiler 3" max from deck.
The end caps must be a triangle shape.(See template)
You may have one fin on the spoiler and two side caps.
The third fin must also be the same dimension as side cap.
It can be located anywhere on the spoiler between the two side caps.
The fin must be in line with the side caps on the front leading edge.
Section 5:
Wheel & Tire Specs OPEN
​
​
SPORTSMAN LATEMODEL
Section 1:
Chassis:
REDCAT BLACKOUT SERIES BRUSHLESS ONLY
Section 2:
Electronics:
Any Radio allowed
SPEED CONTROLLER REDCAT ONLY
MOTOR REDCAT RTR ONLY
BATTERY REDCAT HEXFLY 5800 AND BELOW LIPOS ONLY
Section 3:
Bodies:
CENTER OAKS BODIES BLACKOUT LATEMODEL BODY ONLY
Section 4:
Wheel & Tire Specs:
STOCK BLACKOUT SC & OR XBE TIRES ONLY
SUPER LATEMODEL
​
2WD SCT DIRT LATEMODEL
Section 1:
Chassis:
Must be a stock factory 1/10 scale 2 wheel drive SC truck! The only upgrades
allowed are durability items! Any and all upgrades must be OEM (no LTO chassis, cutting or drilling of stock chassis, and all suspension parts must remain in stock location )
All electronics must be in the stock factory designed location.
No wheel adapters or spacers!
Springs must be SC truck based and cannot be cut or shortened.
Shocks must be SC based and can run any spring, oil, and piston combo.
Shocks must be factory length front and rear.
Section 2:
Electronics:
Any Radio allowed
Any Hard Case 2-cell 7.4 lipo or up to a 6 cell NiCd/NiMh
Any speed controller, no boost must run in spec mode.
Any brush-less 13.5 turn or higher motor, or 12 turn or higher brushed motor 1/10 ONLY
Section 3:
Bodies:
ANY SHORT COARSE LATEMODEL BODY ALLOWED.
No additional wings, flaps, spoilers, wickers, vents will be allowed
Decking is allowed
There will be no metal body parts of any kind. FASTENERS OK
All bodies must completely cover the wheels
Must run a rear bumper (No metal bumpers allowed)
Section 4:
Rear Spoiler Specs:
Rear spoiler can only be as wide as the body at the rear quarter panels.
Rear spoiler 3" max from deck.
The end caps must be a triangle shape.(See template)
You may have one fin on the spoiler and two side caps.
The third fin must also be the same dimension as side cap.
It can be located anywhere on the spoiler between the two side caps.
The fin must be in line with the side caps on the front leading edge.
Section 5:
Wheel & Tire Specs:
Wheels must be the 2.2/3.0 SC wheels, no 1/10 ST or 1/8 buggy wheels
Tires must be the 2.2/3.0 SC tires
OUTLAW LATEMODEL
​
4wd LATEMODEL
Section 1:
Chassis:
Must be a 4WD 11INCH LENGTH WHEEL BASE.. This is a builders class. Any upgrades
allowed as long as chassis fits under a 12" wide body
Wheel adapters or offset susp or chassis allowed AS LONG FITS INSIDE OF BODY
Section 2:
Electronics:
Radio OPEN
BATTERY OPEN
SPEED CONTROLLER OPEN
MOTOR OPEN
Section 3:
Bodies:
Any 1/8 or SC dirt latemodel body production or Homemade.
ANY additional wings, flaps, spoilers, wickers, vents will be allowed
Decking is allowed
There will be no metal body parts of any kind. FASTENERS OK
All bodies must completely cover the wheels NO WIDER THAN 12"
Must run a rear bumper (No metal bumpers allowed)
Section 4:
Rear Spoiler Specs:
Rear spoiler can only be as wide as the body at the rear quarter panels.
Rear spoiler 3" max from deck.
The end caps must be a triangle shape.(See template)
You may have one fin on the spoiler and two side caps.
The third fin must also be the same dimension as side cap.
It can be located anywhere on the spoiler between the two side caps.
The fin must be in line with the side caps on the front leading edge.
Section 5:
Wheel & Tire Specs:
OPEN
​
SPRINT CAR
Section 1:
Chassis:
Must be a stock factory 1/10 scale 2WD SC truck! The only upgrades
allowed are durability items! Any and all upgrades must be OEM (no LTO chassis, cutting or drilling of stock chassis, and all suspension parts must remain in stock location )
All electronics must be in the stock factory designed location.
No wheel adapters or spacers!
Springs must be SC truck based and cannot be cut or shortened.
Shocks must be SC based and can run any spring, oil, and piston combo.
Shocks must be factory length front and rear.
Section 2:
Electronics:
Any Radio allowed
Any Hard Case 2-cell 7.4 lipo or up to a 6 cell NiCd/NiMh
Any speed controller
​
Any motor
Section 3:
Bodies:
Molded one- piece Mcallister or RJspeed bodies only.
7" or 6" molded upper wing
There will be no metal body parts or chassis of any kind. .
Section 4:
Wheel & Tire Specs:
Wheels must be the 2.2/3.0 SC wheels,
No 1/10 ST or 1/8 buggy wheels
No foam tires.
Tires must be the 2.2/3.0 SC rubber tires
1/5 SPORTSMAN Late Model
Section 1
Chassis
Must be 1/5 production based 2 WD 5B buggy chassis.
No shortened, extended,offset or flat (Front kick up) style.
All parts must be stock or after market stock style Baja upgrades ( durability only)
Any and all parts must be flush or in side the tread width. 1/8 tolerance.
All chassis and tires must remain inside the body.
No metal or carbon fiber front bumpers.
Wheel extenders allowed
Adjustable front and rear shock towers allowed.
All parts must be available to the public from a
Store front/Track hobby shop or on line STORE!
No home made chassis or suspension parts of any kind!
Section 2
Engine
Size: 23cc to 30.5cc max
No reed, piston port only
Stock style/size flywheel
Exhaust: Outdoor tracks (track option).
Indoors tracks must run can, silencer is track option
Fuel: Gas only!
Section 3
Bodies
Max over all length 48"
Max width where deck and A post meet and where rear quarter panel and deck meet 20"
Max width at front flopper's widest point 26"
Must have the Woo/Lucas appearance ( No wedge style)
Decking is allowed
Only holes allowed in deck are for Spark plug
There will be no metal body parts of any kind. Roll cage can be metal.
No part of the deck can be higher than 12" from ground to bottom side.
Section 4
Rear Spoiler Specs
Rear spoiler can only be as wide as the body at the rear quarter panels.
Rear spoiler 5" max from deck.
The end caps must be a triangle shape and be in proportion to todays Late Models.
You may have one fin on the spoiler and two side caps.
The third fin must also be the same dimension as side cap.
It can be located anywhere on the spoiler between the two side caps.
The fin must be in line with the side caps on the front leading edge.
Section 5
Wheel & Tire Specs
Rubber tires only!
All wheels must be bead lock buggy based.
Must be 1/5 scale
cutting, siping and grooving are legal
Traction compounds are legal.
Section 6
Electronics
Stability control NOT ALLOWED
Section 7
The track has final say on rules enforcement!
Section 8
The DLMRA is not responsible for any actions by tracks or racers!
Section 9
The DLMRA reserves the right to change any specifications at anytime in the fairness of the hobby!.
​
1/5 OUTLAW LATEMODEL
​
Section 1
Chassis
Must be 1/5 production based 2 WD 5B buggy chassis.
No shortened, extended,offset or flat (Front kick up) style.
All parts must be stock or after market stock style Baja upgrades ( durability only)
Any and all parts must be flush or in side the tread width. 1/8 tolerance.
All chassis and tires must remain inside the body.
No metal or carbon fiber front bumpers.
Wheel extenders allowed
Adjustable front and rear shock towers allowed.
All parts must be available to the public from a
Store front/Track hobby shop or on line STORE!
No home made chassis or suspension parts of any kind!
Section 2
Engine
Size: 23cc to 30.5cc max AFTERMARKET MODIFIED MOTORS ALLOWED
ALLOWED reed, piston port
Stock style/size flywheel
Exhaust: ANY ALLOWED
Indoors tracks must run can, silencer is track option
Fuel: Gas only!
Section 3
Bodies
Max over all length 48"
Max width where deck and A post meet and where rear quarter panel and deck meet 20"
Max width at front flopper's widest point 26"
Must have the Woo/Lucas appearance ( No wedge style)
Decking is allowed
Only holes allowed in deck are for Spark plug
There will be no metal body parts of any kind. Roll cage can be metal.
No part of the deck can be higher than 12" from ground to bottom side.
Section 4
Rear Spoiler Specs
Rear spoiler can only be as wide as the body at the rear quarter panels.
Rear spoiler 5" max from deck.
The end caps must be a triangle shape and be in proportion to todays Late Models.
You may have one fin on the spoiler and two side caps.
The third fin must also be the same dimension as side cap.
It can be located anywhere on the spoiler between the two side caps.
The fin must be in line with the side caps on the front leading edge.
Section 5
Wheel & Tire Specs
All wheels must be bead lock buggy based.
Must be 1/5 scale
cutting, siping and grooving are legal
Traction compounds are legal.
Section 6
Electronics
Stability control ALLOWED
Section 7
The track has final say on rules enforcement!
Section 8
The DLMRA is not responsible for any actions by tracks or racers!
Section 9
The DLMRA reserves the right to change any specifications at anytime in the fairness of the hobby!.
​
​